http://wiki.allscanner.com/zh/guide/firmware
- UPD: Update for BENZ Xentry Diagnosis 2024.09
- 更新: 更新支持 BENZ Xentry Diagnosis 2024.09
- UPD: Update for BENZ Xentry Diagnosis 2024.06
- 更新: 更新支持 BENZ Xentry Diagnosis 2024.06
- FIX: Firmware v1.9.4.0 caused the K-Line failure on BENZ hardware.
- 修正: 固件 V1.9.4.0 引起的 BENZ 硬件 K-Line 失效.
- FIX: TP20 protocol BS_ECU == 1 cause send data failure.
- ADD: Add MxxZB deive model support.
- 修正: TP20 协议 BS_ECU 参数为1时导致发送数据失败.
- 新增: 新增 MxxZB 设备型号支持.
- FIX: TP20 protocol T3_ECU parameter must be verified.
- 修正: TP20 协议 T3_ECU 延时参数有效性检查.
- FIX: CAN_PS and K-Line OBD7 pins can operate simultaneously.
- 修正: CAN_PS 和 K-Line OBD7 引脚可同时工作.
- ADD: Add H6M device model support.
- OPT: Optimize ISO15765 for receive unordered consecutive frame.
- 新增: H6M 设备型号支持.
- 优化: ISO15765 协议接收乱序连续帧(长安非标准).
- FIX: Fix device license invalid when sometimes.
- UPD: Update for BENZ Xentry Diagnosis 2022.09
- 更新: 更新支持 BENZ Xentry Diagnosis 2022.09
NOTE: If XENTRY VCI SN is 00000000 or invalid, Please update VCI firmware and reboot!
注意: 如果 XENTRY VCI 为无效序列号 00000000 或无连接, 请更新 VCI 固件到此最新版本并重启设备！
- OPT: Optimize KL15 signal acquisition(fix KL15 unstable on some Hardware model).
- 优化: 优化 KL15 点火开关信号采集(修正部分硬件型号KL15信号不稳定).
- FIX: TP20 protocol transmit segment data error process(programming interrupt).
- 修正: TP20 协议发送长帧数据错误处理(编程中断).
- FIX: TP20 protocol receive segment data break with testconn ACK.
- 修正: TP20 协议接收分段数据时被 连接测试回应 打断.
- UPD: Update for BENZ Xentry Diagnosis 2021.09 和 2021.12
NOTE: If XENTRY VCI SN is 00000000 and invalid, Please update VCI firmware and reboot!
- 更新: 更新支持 BENZ Xentry Diagnosis 2021.09 和 2021.12
注意: 如果 XENTRY VCI 为无效序列号 00000000, 请更新 VCI 固件到此最新版本并重启设备！
- OPT: TP20 protocol support DoNet mode.
- OPT: TP16 protocol support DoNet mode.
- OPT: ISO9141/ISO14230 KLine idle wait process.
- FIX: J1939 protocol PGN receive process(John Deere EDL).
- ADD: DA device model support.
- ADD: MAX device model support.
- 优化: TP20 协议支持 DoNet 模式.
- 优化: TP16 协议支持 DoNet 模式.
- 优化: ISO9141/ISO14230 KLine 等待空闲处理.
- 修正: J1939 协议 PGN 接收不完整(John Deere EDL).
- 新增: DA 设备型号支持.
- 新增: MAX 设备型号支持.
- MOD: ISO15765 P2MAX.
- ADD: ISO14230 PID_FORCE_WAIT_IDLE force to wait idle when init.
- ADD: KT Device model support.
- 修改: ISO15765 P2MAX.
- 新增: ISO14230 PID_FORCE_WAIT_IDLE 连续初始化时强制等待空闲.
- 新增: KT设备型号支持.
- FIX: Fix J1850-PWM protocol for Ford IDS OBD mode diagnosis.
- 修正: J1850-PWM 协议 Ford IDS OBD 模式诊断.
- FIX: Fix VCI software may crash after soft reset.
- FIX: Fix license read error in some condition.
- OPT: Optimize remote diagnosis DoNet connection stability.
- 修正: 软复位后可能导致 VCI 软件崩溃无响应.
- 修正: 部分情况下读取授权失败.
- 优化: 定时消息发送失败时的处理.
- FIX: TP20 protocol programming failure.
- FIX: ISO15765 P2Max process (Ford mondeo test error).
- OPT: Optimize remote diagnosis DoNet connection stability.
- 修正: TP20 协议编程失败.
- 修正: ISO15765 协议 P2Max 超时处理 (Ford Mondeo 测试错误).
- 优化: 优化远程诊断 DoNet 连接稳定性.
- UPD: Update new platform with SDK v1.8.0.0
- ADD: LIN bus protocol.
- FIX: OBD IGSW Pin voltage read.
- 更新 同步更新新平台 SDK v1.8.0.0
- 新增 LIN 总线协议.
- 优化 OBD 点火电压信号读取.
- FIX: TP20 protocol MNST repeat send process(ODIS engineering programming).
- FIX: ISO15765_EXT_BMW simulator send(DoNET remote diagnosis).
- 修复 TP20 协议 MNTB 重发处理(ODIS工程师编程).
- 修复 ISO15765_EXT_BMW 模拟发送(DoNET远程模式).
- Add ISO11898 protocol multiple send mode (for DoNet).
- 新增 ISO11898 协议增加 MULTI 多帧发送模式 (远程诊断).
- Fix ISO15765 protocol receive message with mixed ext address(PORSCHE 970)
- 修正 ISO15765 协议接收时智能识别是否带扩展地址/两种模式混合(PROSCHE 970)
- Fix Some hardware (H6 serials) read iginition voltage
- Fix 5 Baud simulation receive
- 修正 部分硬件(H6系列)读取点火电压
- 修正 5 Baud 模拟接收
- Add FACTORY SerialNumber
- Add Fast software reset
- Fix 29Bit CANID filter clear error(BENZ ACTORS 963)
- Fix J1939 protocol send long frame(CAT Flash)
- Imp Memory space
- 新增 FACTORY 序列号功能
- 新增 快速软复位功能
- 修正 29bit CANID 过滤器清除错误 (BENZ ACTROS 963)
- 修正 J1939 协议发送长帧 (CAT Flash)
- 优化 内存空间
- Fix ISO14230/9194 compatible with BENZ KW2K2N MR OBD-9 bus.
- 修正 ISO14230/9141 兼容 BENZ KW2K2N MR OBD-9总线.
- Imp J1939 protocol channel support multiple ECU network communication(CAT-C9).
- Imp Automatically identify the interface using the SN.
- 优化 J1939 协议通道支持多个ECU网络节点通信(CAT-C9).
- 优化 根据序列号SN自动识别接口.
- Add Support new bus mux chip.
- Upd VCXBoot v1.5.1.0
- 新增 支持新的总线开关芯片.
- 更新 VCXBoot v1.5.1.0
- Fix IO Expasion chip identification.
- Imp ISO15765 performance for receive 4KB message(BENZ DTS read all coding).
- 优化 ISO15765 接收 4KB 长帧处理性能(BENZ DTS工程师读取整车设码).
- Fix ISO15765 FlowControl state 31 process(BENZ 205 SCN Error).
- Add Support H6P VCI interface identify.
- 修正 ISO15765 流控制状态31处理(BENZ 205 SCN设码错误).
- 新增 支持 H6P VCI 接口自动识别.
- Upd VCXBoot v1.5.0.0 multiple app boot and update.
- Fix J1939 flow control process when broadcast mixed with normal message(CUMMINS-QSC8.3).
- Imp USB connection status and other etc.
- 更新 VCXBoot v1.5.0.0 多分区引导和固件更新.
- 修正 J1939 多帧消息与广播消息混合时的流控制处理(CUMMINS-QSC8.3).
- 优化 USB 连接状态和其他.
- Fix J1939 Filter PGN=00EF00 with connection management(CAT-320D2)
- Fix J1939 broadcast filter and broadcast mixed with normal message(CUMMINS-QSM11).
- Imp Host and device communiction performance (Fix communication CS error sometimes).
- 修正 J1939 过滤器 PGN=00EF00 增加连接管理(CAT-320D2).
- 修正 J1939 广播消息过滤, 广播消息与普通多帧消息混合(CUMMINS-QSM11).
- 优化 主机和设备之间通信效率(修复通信校验CS可能出错).
- Fix ISO15765 flow control frame send error.
- Fix CAN2 driver control process.
- Add V83 new hardware bus switch(Read OBD Pin Voltage).
- Fix J1708 pin initiation.
- 修正 ISO15765 流控制帧发送错误.
- 修正 CAN2 驱动器控制信号逻辑顺序.
- 新增 V83 新版本硬件总线开关切换(读OBD引脚电压).
- 修正 J1708 引脚初始化.
- Fix BENZ C6 CAN Bus KL15 signal filter
- Fix BENZ C6 MBISO 5BPS initialization
- 修正 支持 BENZ C6 CAN 总线点火信号过滤
- 修正 支持 BENZ C6 MBISO 协议 5BPS 初始化
- Fix HS-CAN error when multiple channel working (JLR).
- 修正 CAN 多通道工作时 HS-CAN 可能通信错误 (路虎第一路CAN不能测以及止动装置错误).
- Fix J1939 protocol error for CUMMINS CM850.
- 修正 J1939 协议测试 CUMMINS CM850 连接错误.
- Add Expasion DoIP device information sync with VCX.
- 增加 扩展设备DOIP 与 VCX 同步扩展信息.
- Optimize CAN PS switch logic.
- Optimize TP20 protocol for J2534.
- Fix KW1281 reset to IDLE when tx error.
- 优化 NANO 系列 CAN PS 引脚选择逻辑.
- 优化 TP20 协议符合 J2534标准.
- 修正 KW1281 发送错误时恢复空闲状态.
- Fix v1.3.4.0 error for CAN OBD12/13.
- 修正 v1.3.4.0 固件引起的 CAN OBD12/13 错误.
- Fix CAN lost data in callback when multi channel scanning(PORSCHE).
- Fix CAN block filter do not set to hardware.
- Add J1850 VPW and PWM switch(PB3).
- 修正 CAN 回掉处理丢失数据, 当多通道扫描时(PORSCHE).
- 修正 CAN 阻止过滤器不需要配置到硬件.
- 增加 J1850 VPM 和 PWM 切换开关(PB3).
- Fix CAN frame queue crash when receive large amount data(BENZ).
- Optimize CAN rx handler and FIFO.
- Optimize CAN reinit.
- Optimize CAN filter overflow.
- 修正 CAN 接收海量数据时缓冲队列溢出设备死机(BENZ).
- 优化 CAN 接收中断和FIFO.
- 优化 CAN 重新初始化.
- 优化 CAN 过滤器溢出处理.
- Fix SWCAN error for GM GDS2.
- Fix CAN filter clear.
- Modify CAN hardware filter for multiple channel(for BENZ).
- Fix OBD pin voltage read for new VCX-PRO device.
- Fix ISO15765 standard extend addr error.
- Fix CAN baud 800k error.
- Fix TP20 Channel Setup ID dynamically alloc.
- Fix ISO15765 free protocol_buf after rx segment message break.
- Fix BMW_KCAN extend address update automatic.
- Remove IDE bit from CAN filter
- Fix BMW_KCAN extend address(TX and RX different).
- Fix OPEL KW82 protocol for GM Tech2Win.
- Fix ISO15765 recv error when RAW CAN message mixed.
- Fix TP20 Channel request RX ID start from 0.
- Add timer message PTIMER_FLAG_TX_INST.
- Fix 29bit CAN ID filter.
- Fix KW1281 protocol timer when idle.
- Add TP20 can bus loopback message.
- Fix some error.
- Fix ISO15765 receive message as ISO15765 when Filter OFF.
- Fix ISO15765 receive message as RAW when Filter do not set FlowControl.
- Fix ISO15765 receive RX_START flag message.
- Fix DeviceInfo.HwName to be correct with SerialNo.
- Fix ISO14230 receive KWP frame length process without P1MAX.
- Fix ISO15765 extend addr process (Toyota IMMO).
- Fix Opel KW82 protocol.
- Add protocol ISO14230, KW82.
- Change protocol KW81 to KW1281.
- A lot of optimize.
- Optimize Protocol Timer Msg to surpport with TXFLAG(GM J2534 programming)
- Optimize Protocol Timer Msg size to 16 bytes
- Optimize and correct J1850 VPW Bit timming issure(GM J2534 programming)
- Correct J1850 CRC Algorithm
- Correct J1850 VPW init state to IDLE
- Optimize and correct J1850 PWM Bit timming issure(FORD J2534 progarmming)
- Optimize VCX_GetDevInfo & DecodeSerial
- Auto set hardware comm interface(BT,WIFI) by device serialNo
- Optimize for WiFi and BT communication process automatically
- Add shell AT command for BT
- Optimize other
- Fix J1939 AC, VCX will return the Address Claime message from net.
- Fix J1939 AC, When RX request AC, VCX will TX the Address After Address Claime done.
- Fix J1939 Network Manage, tx CTS Must after AC Done.
- Fix J1850 PWM comm rx fault after VPW deinit(TIM DeInit not correct)
- Optimize ISO15756 add filter time delay.
- Optimize J1708 TX timing process.
- Fix J1939 rx error for CTS & EOMA (tx long message when calibration)
- VCX Boot and App update to v1.1.0.0
- Migrate to New VCX Secure Platform
- Fix some project and utils files
- Fix ISO15765 TXFLAG_CAN_PAD not effect the global param.
- Fix ISO15765 RX FlowCtrl timeout process.
- Add TXFLAG_TX_IND to enable receive TX Indication (TX_DONE)
- Fix ISO15765 FlowCtrl RX msg restore to queue.
- Fix ISO15765 Default CAN Pad byte to 0x00.
- Go into DFU mode when secure error.
- Other optimize.
- Fix TP16/TP20 T1 T3 time set to ECU
- Fix ISO15765 receive RAW CAN data packet 6A0/6A1
- Fix CAN2 filter lost when CAN1 init
- Optimize VCX ReqLicense time.
- Optimize memory to 112KB for all protocol channel use.
- Fix CAN 29bit filter error for J1939
- Fix CAN Bus2 filter error for JLR.
- Fix J1939 Protocol (bus filter not reg after init).
- Fix Ford PWM error (bus IDLE state).
- Fix CAN Bus2 filter error for JLR.
- Add GM J1850VPW Protocol support for VCX-NANO.
- Optimize FORD J1850 PWM Protocol Check Bus Passive State Delay(2N3904)
- Optimize FORD J1850 PWM Protocol Tx Bus Collision Timeout (10*50ms)
- Ford J1850PWM Protocol Now support ALL Products of VCX Platform.
- Fix Hardware Verification Error(4 Led flashing) in some hardware.
- Add J1850PWM Protocol for Ford.
- Fix CAN Filter to MAX 56 each channel.
- Other completed.
- Add HD J1939/J1708 Support.
- Other completed.
- Fix PIWIS-II scanning all system
- Fix PIWIS-II programming (ISO15765 tx_stmin delay)